加工級別 | 注塑級,脫模級 | 特性級別 | 耐磨 |
|
產品簡述
加工級別 | 注塑級,脫模級 | 特性級別 | 耐磨 |
用途:應用于汽車排檔,機用存儲原料
備注:特點:有色,高粘綢性,分子量分布密,可焊接于超聲波。
詳細數據
訂購指南
性能項目 | 試驗條件[狀態] | 測試方法 | 測試數據 | 數據單位 | ||
物理性能 | 吸水均衡性 | 50% RHL;DAM | Similar to ISO 62 | 2.6 | % | |
粘性系數測試 | Viscosity Number;DAM | ISO 307 | 275 | cm3/g | ||
吸水飽和性 | - | DAM | ASTM D570 | 8.5 | % | |
- | DAM | Similar to ISO 62 | 8.5 | % | ||
密度 | - | DAM | ASTM D792 | 1.14 | g/cc | |
- | DAM | ISO 1183 | 1.14 | g/cc | ||
線型模量收縮率橫向 | 2.0mm;DAM | ISO 294-4 | 0.014 | cm/cm | ||
線型模量收縮率 | - | Parallel;2.0mm;DAM | ISO 294-4 | 0.014 | cm/cm | |
- | Flow;3.2mm(0.126in);DAM | ISO 294-4 | 0.015 | cm/cm | ||
吸水率 | immersion 24h;DAM | ASTM D570 | 1.2 | % | ||
機械性能 | Charpy缺口沖擊 | - | DAM | ISO 179/1eA | 0.6 | J/cm2 |
- | 50% RH | ISO 179/1eA | 2 | J/cm2 | ||
低溫下charpy缺口沖擊 | - | -30℃;50% RH | ISO 179/1eU | 0.4 | J/cm2 | |
- | -30℃;DAM | ISO 179/1eU | 0.6 | J/cm2 | ||
拉伸屈服強度 | - | 50% RH | ISO 527 | 55 | MPa | |
- | 50% RH | ASTM D638 | 59 | MPa | ||
- | DAM | ISO 527 | 83 | MPa | ||
彎曲模量 | - | 50% RH | ISO 178 | 1.07 | GPa | |
- | 50% RH | ASTM D790 | 1.21 | GPa | ||
- | DAM | ISO 178 | 2.8 | GPa | ||
- | DAM | ASTM D790 | 2.83 | GPa | ||
洛氏硬度 | - | DAM | ASTM D785 | 80 | M | |
- | DAM | ASTM D785 | 121 | R | ||
拉伸模量 | - | 50% RH | ISO 527 | 1.3 | GPa | |
- | DAM | ISO 527 | 3.1 | GPa | ||
低溫下charpy抗沖擊強度 | - | -30℃;50% RH | ISO 179/1eU | NB | - | |
- | -30℃;DAM | ISO 179/1eU | NB | - | ||
Charpy抗沖擊強度 | - | 50% RH | ISO 179/1eU | NB | - | |
- | DAM | ISO 179/1eU | NB | - | ||
IZOD沖擊 | - | DAM | ASTM D256 | 0.64 | J/cm | |
- | 50% RH | ASTM D256 | 1.33 | J/cm | ||
拉伸率 | - | 50% RH | ASTM D638 | 30 | % | |
- | DAM | ISO 527 | 4.4 | % | ||
- | DAM | ASTM D638 | 5 | % | ||
IZOD缺口沖擊 | - | 50% RH | ISO 180/1A | 23 | KJ/m2 | |
- | DAM | ISO 180/1A | 6 | KJ/m2 | ||
IZOD抗沖擊強度 | - | DAM | ISO 180/1U | NB | - | |
- | 50% RH | ISO 180/1U | NB | - | ||
拉力抗沖強度 | Long specimen;DAM | ASTM D1822 | 535 | KJ/m2 | ||
純強度 | - | 50% RH | ASTM D732 | 63 | MPa | |
- | DAM | ASTM D732 | 66 | MPa | ||
IZOD抗沖 | - | 50% RH | ASTM D256 | 0.27 | J/cm | |
- | DAM | ASTM D256 | 0.32 | J/cm | ||
拉伸強度 | - | 50% RH | ASTM D638 | 77 | MPa | |
- | DAM | ASTM D638 | 85 | MPa | ||
電氣性能 | 體積電阻率 | - | 50% RH | IEC 60093 | 1e+011 | ohm-cm |
- | DAM | IEC 60093 | 1e+013 | ohm-cm | ||
介電常數 | - | 1MHz;50%RH | IEC 60250 | 4.2 | - | |
- | 100Hz;DAM | IEC 60250 | 4.3 | - | ||
- | 50%RH | ASTM D150 | 4.6 | - | ||
- | 50%RH | ASTM D150 | 7 | - | ||
- | 50%RH | ASTM D150 | 8 | - | ||
介電常數 | - | 100Hz;50%RH | IEC 60250 | 10.03 | - | |
- | DAM | ASTM D150 | 3.6 | - | ||
- | MHz;DAM | IEC 60250 | 3.6 | - | ||
- | DAM | ASTM D150 | 3.9 | - | ||
- | DAM | ASTM D150 | 4 | - | ||
介電損耗因素 | - | 100Hz;DAM | ASTM D150 | 0.01 | - | |
- | 100Hz;DAM | IEC 60250 | 0.015 | - | ||
- | 1KHz;DAM | ASTM D150 | 0.02 | - | ||
- | 1MHz;DAM | ASTM D150 | 0.02 | - | ||
加工性能 | 熔融溫度 | DAM | 280-300 | ℃ | ||
干燥損失率 | DAM | Max0.05 | % | |||
模量溫度 | DAM | 50-90 | ℃ | |||
熱性能 | ULRTI,機械性 | - | 3.0mm;DAM | UL 746B | 85 | ℃ |
- | 1.5MM;DAM | UL 746B | 85 | ℃ | ||
熱膨脹系數 | 線型20℃下橫流 | 23-55℃(73-130°F);DAM | ASTM E831 | 100 | μm/m-℃ | |
線型20℃下橫流 | 23-55℃(73-130°F);DAM | ISO 11359-1/-2 | 100 | μm/m-℃ | ||
ULRTI,電氣性 | - | 3.0mm;DAM | UL 746B | 125 | ℃ | |
- | 1.5MM;DAM | UL 746B | 125 | ℃ | ||
氧氣指數 | DAM | ISO 4589-1/-2 | 28 | % | ||
脆化溫度 | DAM | ASTM D746 | -100 | ℃ | ||
熔點 | - | 10℃/min;DAM | ISO 11357-1-3 | 262 | ℃ | |
- | DAM | ASTM D3418 | 263 | ℃ | ||
變形溫度 | - | at 0.46 MPa | ISO 75-1/-2 | 200 | ℃ | |
- | at 0.46 MPa | ASTM D648 | 210 | ℃ | ||
- | at 1.8 MPa | ASTM D648 | 65 | ℃ | ||
- | at 1.8 MPa | ISO 75-1/-2 | 70 | ℃ | ||
燃燒性 | - | 1.5mm;DAM | UL 94 | HB | - | |
- | 1.5mm;DAM | IEC 60695-11-10 | HB | - | ||
- | 0.71mm;DAM | IEC 60695-11-10 | HB | - | ||
- | 0.71mm;DAM | UL 94 | HB | - | ||
- | 3.0mm;DAM | IEC 60695-11-10 | HB | - | ||
- | 3.0mm;DAM | UL 94 | HB | - | ||
熱膨脹系數 | 線型20℃ | Parallel;23-55℃(73-130°F);DAM | ASTM E831 | 100 | μm/m-℃ | |
線型20℃ | Parallel;23-55℃(73-130°F);DAM | ISO 11359-1/-2 | 100 | μm/m-℃ | ||
ULRTI,抗沖性機械性能 | - | 1.5mm;DAM | UL 746B | 75 | ℃ | |
- | 3.0mm;DAM | UL 746B | 75 | ℃ | ||
其它性能 | 顏色 | 天然 | ||||
形式 | 粒子 | |||||
加工方法 | - | - | - | 注塑成型 | - | |
- | - | - | 擠出 | - | ||
- | - | - | 注塑 | - | ||
- | - | - | 涂層 | - |